Xavax 111398 Non-return valve, with 2 hose clamps, for hoses up to 10mm diameter, Silver

Product Information

Washing machines need a hot and cold feed (Most machines are able to run on a cold only supply, but you are asking the machine to heat the water up. This will have been done elsewhere in the house for your domestic hot water so why pay twice!) The hot supply can be taken from most hot water systems but not a single outlet water heater. Browse our guide to common washing machine repair issues, which is sure to help. What should I do with my old washing machine? What’s more, the installation of these machines can be quite costly. This article aims to answer all your questions while teaching you how to install your own washing machine.

Under sink plumbing advice - Waste water back-flow into Under sink plumbing advice - Waste water back-flow into

If your washing machine is going to be more than a hose length away from a suitable place to put this type of connection, you will have to insert an ordinary T piece (the installation is the same if you use a compression fitting) and instead of the hose going on the T, another copper pipe is fitted, taking the water to the location of the machine. Flashing lights, error code appearing or your washing machine just doesn't work?Do you need help to diagnose a fault with your washing machine, find out what the problem is, what parts you need to repair it? Use our totally free forums for help from repair technicians.Solvent weld waste: Again, cut and sand the pipe. Next, use solvent cement to attach the pipe to the fitting. You will need to connect the waste pipe to the foul water sewer instead of the rainwater soakaway. To install the waste pipe, cut a hole in your wall just bigger than the width of the pipe. This will usually be 4cm but could be smaller. Ensure the lip of the standpipe is 30 inches from the ground. To finish, it is a good idea to either install a non-return valve or hook your drain hose up and under your worktop. Hiring a professional You will need to locate the hose connections under your sink and should switch off your water supply before beginning. Connect the washing machine as described in our ‘how to plumb in a washing machine’ section, and it is worth keeping the drain cap under your sink for any future washing machine installations. How to plumb in a washing machine in a caravan There doesn't appear to be anything obviously wrong with that setup - the height of the hose connections on to the under-sink waste pipe look to be fine.

Plumb in a Washing Machine | Checkatrade Learn How to Plumb in a Washing Machine | Checkatrade

We will also look further into how to plumb in a washing machine waste pipe, how to plumb in a washing machine under the sink and more. So, keep reading to learn skills that will last a lifetime. How to plumb in a washing machine First, choose where to position your washing machine In the second picture it appears that any waste discharged from the sink would make its way into either the dishwasher or the washing machine by gravity, compounded by the fact that the appliance union appears to be level with or slightly below the u-bend outlet. I see this quite a lot and it is simply rectified by rotating the appliance inlets and raising the level of the uppermost bend in their hoses.The short of it is that, if the appliance was installed correctly in accordance with the instructions (which installers rarely, if ever, seem to bother reading) then the problem should never occur. Carefully consider the best location for your new washing machine, it should be somewhere convenient with easy access and close to a water source.

way valve for washing machine outlet? Is there a one way valve for washing machine outlet?

These fittings are available with 2 nozzles to take a dishwasher as well and can also be fitted to a double bowl or bowl + half sink. Kits are available for this. There is also a self cutting, non return valve which will clamp directly onto your waste pipe, but this must be installed before a trap. I'd undo all the white pipes under the sink - they are all dismantleable. See if it's clean and free-flowing. If you are too far away from the sink for these fittings, or the manufacturers instructions do not allow this type of waste removal, a stand pipe needs to be fitted to the wall. This then connects to the existing drainage system in your kitchen as the next photograph shows, or it can be taken out through a purpose made hole in the

Hiring a professional

Top left is a T piece valve that is inserted into the run of the pipe you are working on. The handle is colour coded for hot and cold. The appropriate washing machine hose screws onto the centre section and the handle turns the water on and off. To Insert this type of valve, a section of pipe 18mm long needs to be cut out of your feed pipe. We use a pipe slice for these cuts, this can be seen below and allows you to cut in very tight spaces. You clip it onto the pipe and turn to cut.